ndif
#define CONSOLE_BAUD_RATE 57600


#undef INCLUDE_ENV_VARS /* unix compatable environment variables */
#undef INCLUDE_TIMEX /* timexLib for exec timing */
#undef INCLUDE_HW_FP
#undef INCLUDE_TFTP_CLIENT /* used by autoboot from ftp server*/

#define INCLUDE_SW_FP
#define INCLUDE_ELF
#define INCLUDE_NET_SHOW
#define INCLUDE_PING
#undef INCLUDE_DEMO /* only for vxWorks bsp test */
#define ETHERNET_ADR_SET /* only for bootrom used */
#define INCLUDE_USER_APPL /* Startup the user''s application in dos makefile project */
#undef PCIDEBUG

#ifdef INCLUDE_USER_APPL
#define USER_APPL_INIT _appEntry()
#endif

#endif /* INCconfigh */
#if defined(PRJ_BUILD)
#include "prjParams.h"
#endif

Makefile文件配置

# Makefile - make rules for board
#
#*/

CPU = PPC40x
TOOL = gnu

TGT_DIR=$(WIND_BASE)/target
include $(TGT_DIR)/h/make/defs.bsp
include $(TGT_DIR)/h/make/make.$(CPU)$(TOOL)
include $(TGT_DIR)/h/make/defs.$(WIND_HOST_TYPE)

## Only redefine make definitions below this point, or your definitions will
## be overwritten by the makefile stubs above.


TARGET_DIR = xxx
VENDOR = IBM
BOARD = xxx

RELEASE = vxWorks vxWorks.st bootrom_uncmp.hex

USR_ENTRY = usrInit


# ROM_TEXT_ADRS, ROM_SIZE, RAM_HIGH_ADRS, 和RAM_LOW_ADRS 在config.h,Makefile和Makefile.*文件中 # 都要定義,且必須要保持一致,

ROM_TEXT_ADRS = fff80100                 # ROM 起始地址
ROM_SIZE = 0007f000                      # ROM 空間大小

RAM_LOW_ADRS = 00010000                  # RAM 低地址 vxWorks */
RAM_HIGH_ADRS = 00C00000                 # RAM 高地址存儲 bootrom */

HEX_FLAGS = -a 100

#ADDED_CFLAGS = -gdwarf -O0 # for debug

MACH_EXTRA = appentry.o                # 注意:這里加載用戶的程序模塊,程序調用在usrRoot()

BOOTCONFIG = bootconfig.c               # bsp bootconfig.c for bootrom


## Only redefine make definitions above this point, or the expansion of
## makefile target dependencies may be incorrect.

include $(TGT_DIR)/h/make/rules.bsp
include $(TGT_DIR)/h/make/rules.$(WIND_HOST_TYPE)

　 Tornado for x86下BSP的生成,下載和Target Server的配置實例，Pentium主機，3Com網卡，軟盤引導，ftp下載VxWorks映像。

     1.在C:\Tornado\target\config\pcPentium目錄下修改BSP文件config.h。

#elif (CPU_VARIANT == PENTIUM)
#define DEFAULT_BOOT_LINE 
"elt(0,0)HOST:c:\\Tornado\\target\\config\\pcPentium\\vxWorks 
h=90.0.0.3 e=90.0.0.50 u=target pw=target tn=target"

#define INCLUDE_ELT //3Com網卡
#define INCLUDE_END //END驅動

2.打開Tornado選擇新建一個bootable vxworks image，選擇建 A BSP，選擇
  pcPentium，建完后編譯就可以在相應的目錄下生成vxworks的映像文件。

3.制作bootrom；選擇Build Boot Rom，選擇pcPentium,再選擇bootrom_uncmp，
  生成 bootrom_uncmp。拷貝 bootrom_uncmp到host\x86-win32\bin下，插入空白
  盤到軟區，在dos界面進入目錄host\x86-win32\bin下，用命令"mkboot a: 
  bootrom_uncmp "生成引導盤 

4. 在Start > Programs > Tornado2 > FTP Server，點開Security下的
  user/rights菜單，新建用戶User Name:target，Password:target，Home 
  Directory為VxWorks映像所在目錄如 C:\Tornado\target\config\pcPentium\。
  注意這些配置要和config.h中的一致。

5.將bootrom的啟動盤插入目標機的軟驅，啟動目標機，系統從軟驅啟動，隨后登
  陸FTP，從主機下載vxworks文件，目標機提示7秒內按任意鍵選擇Boot方式（手工
  ，自動），手工方式可對FTP用戶，口令，IP等參數進行修改。
  通常是等待7秒后系統autoboot。
  

屏幕顯示：

Attached TCP/IP interface to elt0.
Attaching network interface lo0... done. //TCP/IP網絡連接成功

Loading... 602128 //通過ftp下載VxWorks映像
Starting at 0x01080000 //下載成功，從RAM_LOW_ADRS 0x01080000
開始執行VxWorks系統

Attached TCP/IP interface to elt unit 0
Attaching interface lo0...done //TCP/IP網絡連接成功
(注意這里網絡初始化成功和上邊的不同，上邊是Bootrom映像網絡初始化來下載VxWorks,這里VxWorks系統初始化網絡。)

VxWorks

Copyright 1984-1998 Wind River Systems, Inc.

CPU: xxxx --- Intel x82 
VxWorks: 5.4
BSP version: 1.2/4
Creation date: Jan xx 2001
WDB: Ready.

至此目標機系統啟動完成。


6.配置Target Server下載應用程序.

打開Tornado，在Tools菜單下選擇Target Sever再選擇configure進行配置(Tools 
> Target Server > Configure > New)給出Target Server名字描述如net00.在
(Target Server Properties > Back End)選擇WdbRpc. Target Name/IP Address 
框內輸入Target的IP: 90.0.0.50. 
Core File and Symbols選項(Target Server Properties > Core File and 
Symbols)： C:\Tornado\target\config\pcPentium\vxWorks等等。
配置的內容根據系統的具體情況定。點擊Launch啟動Target Sever，隨后在主界
面下選擇已啟動的Target Sever就可以下載 *.o或*.out程序。