| 以文本方式查看主題 - 曙海教育集團論壇 (http://www.scb-ycwb.com/bbs/index.asp) -- Linux系統開發 (http://www.scb-ycwb.com/bbs/list.asp?boardid=34) ---- SBC-2410X開發板不能啟動LINUX系統 (http://www.scb-ycwb.com/bbs/dispbbs.asp?boardid=34&id=1788) |
| -- 作者：wangxinxin -- 發布時間：2010-11-25 13:52:38 -- SBC-2410X開發板不能啟動LINUX系統 系統采用REDHAT LINUX 9.0,按照手冊建立好開發環境，順利用Jflash 燒寫vivi 到Nand Flash.但在使用minicom通過xmodem協議使用load flash kernel x命令下載內核卻失敗(內核版本為zImage-yaffs-v6-6448,是光盤上所帶的，大小為894K)，提示信息如下所示： Retry 0: NAK on sector Retry 0: NAK on sector Retry 0: Retry Count Exceeded Transfer incomplete READY: press any key to continue... 然后在windows 2000 下通過超級終端使用load flash kernel x命令下載內核也失敗，信息如下： vivi> load flash kernel x Ready for downloading using xmodem... Waiting... Downloaded file at 0x30000000, size = 914560 bytes An image size is too large to write flash. wanted = 0x000c0000, loaded = 0x000df480 然后用load flash 0x00030000 0x000df480 x下載內核成功 vivi> load flash 0x00030000 0x000df480 x Ready for downloading using xmodem... Waiting... Downloaded file at 0x30000000, size = 914560 bytes Found block size = 0x000e0000 Erasing... ... done Writing... ... done Written 914560 bytes 然后進入linux 1、通過ifconfig eth0 192.168.0.1 設置IP 2、通過 /etc/init.d/nfs restart 啟動nfs服務(/etc/exports已設置好) 3、在vivi提示符模式下輸入命令參數，使用nfs啟動系統時卻進不了系統，一直停在 Booting Linux......，具體信息如下 Welcome to minicom 2.00.0 OPTIONS: History Buffer, F-key Macros, Search History Buffer, I18n Compiled on Jan 25 2003, 00:15:18. Press CTRL-A Z for help on special keys VIVI version 0.1.4 (eady@eady.mizi.com) (gcc version 2.95.3 20010315 (release)) #0.1.4 .. 6宀?29 14:21:19 KST 2003 MMU table base address = 0x33DFC000 Succeed memory mapping. NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung K9D1208V0M) Found saved vivi parameters. Press Return to start the LINUX now, any other key for vivi type "help" for help. vivi> param set linux_cmd_line "console=ttyS0 root=/dev/nfs nfsroot=192.168.0.1:/friendly-arm/root ip=192.168.0.69:192.168.0.1:192.168.0.1:255"Change linux command line to "console=ttyS0 root=/dev/nfs nfsroot=192.168.0.1:/friendly-arm/root ip=192.168.0.69:192.168.0.1:192.168.0.1:255.2"vivi> boot Copy linux kernel from 0x00030000 to 0x30008000, size = 0x000c0000 ... done zImage magic = 0x016f2818 Setup linux parameters at 0x30000100 linux command line is: "console=ttyS0 root=/dev/nfs nfsroot=192.168.0.1:/friendly-arm/root ip=192.168.0.69:192.168.0.1:192.168.0.1:255.255.255"MACH_TYPE = 193 NOW, Booting Linux...... 我在vivi下用part show命令，顯示如下 vivi> part show mtdpart info. (4 partitions) name offset size flag ------------------------------------------------ vivi : 0x00000000 0x00020000 0 128k param : 0x00020000 0x00010000 0 64k kernel : 0x00030000 0x000c0000 0 768k root : 0x00100000 0x00140000 4 1M+256k vivi> |